Silicon Laboratories Ethernet-DK Manuel d'utilisateur

Rev. 0.6 1/11 Copyright © 2011 by Silicon Laboratories Ethernet-DKEthernet-DKEMBEDDED ETHERNET DEVELOPMENT KIT USER’S GUIDE1. OverviewThe Embedded Et

Ethernet-DK10 Rev. 0.65. In the System Settings section of the left window, select IP Addresses. 6. In the right window, set the Source IP Address to

Ethernet-DKRev. 0.6 119. Save the selected configuration using the FileSave As menu. 10. Generate a new project with supporting firmware by selecting

Ethernet-DK12 Rev. 0.66.1.2. Programming the MCUWe will now build the project created by the TCP/IP Configuration Wizard and download the firmware to

Ethernet-DKRev. 0.6 135. Verify the Compiler and Linker tabs are pointing to the C51.exe (compiler) and BL51.exe (linker) files in C:\Keil\C51\BIN in

Ethernet-DK14 Rev. 0.68. Click the Connect button in the toolbar or select DebugConnect from the menu. Note: If you receive the error message “Commun

Ethernet-DKRev. 0.6 156.1.3. Testing Connectivity Using PINGAfter pressing GO, the MCU will be executing the TCP/IP stack firmware. The LEDs on the RJ

Ethernet-DK16 Rev. 0.66.2. Stage 2—Basic Web Server with DHCP and Netfinder CapabilityIn the first stage of the demo, we learned how to generate firm

Ethernet-DKRev. 0.6 175. Save the selected configuration using the FileSave As menu. 6. Generate a new project with supporting firmware by selecting

Ethernet-DK18 Rev. 0.66.2.2. Programming the MCUWe will now build the project created by the TCP/IP Configuration Wizard and download the firmware to

Ethernet-DKRev. 0.6 195. Verify the Compiler and Linker tabs are pointing to the C51.exe (compiler) and BL51.exe (linker) files in C:\Keil\C51\BIN in

Ethernet-DK2 Rev. 0.62. Kit ContentsThe Embedded Ethernet Development Kit contains the following items: C8051F120 Target Board AB4 Ethernet Develop

Ethernet-DK20 Rev. 0.68. Click the Connect button in the toolbar or select DebugConnect from the menu. Note: If you receive the error message “Commun

Ethernet-DKRev. 0.6 216.2.3. Finding the Embedded SystemWe will now search for embedded systems on the network.Note: The Netfinder utility v1.0 is not

Ethernet-DK22 Rev. 0.65. The default web browser should launch and display the home page served by the embedded web server. The same result can be ach

Ethernet-DKRev. 0.6 237. Enter the IP address, subnet mask, and default gateway (if known) into the ‘Assign IP Address’ dialog and press OK. See Appen

Ethernet-DK24 Rev. 0.610. The default web browser should launch and display the home page served by the embedded web server. The same result can be ac

Ethernet-DKRev. 0.6 256.3. Stage 3—Configuring MAC and IP Addresses over the Serial PortIn the first two stages of the demo, we learned how to genera

Ethernet-DK26 Rev. 0.66.3.3. Programming the IP AddressNow the MCU will be running the new firmware and blinking the green LED (P1.6) to indicate that

Ethernet-DKRev. 0.6 276.4. Stage 4—Adding Web Server ContentIn the first three stages of the demo, we learned how to make an embedded web server, fin

Ethernet-DK28 Rev. 0.66.4.3. Re-Building the Project and Viewing ResultsOnce the file arrays are updated, it is time to re-build the project and view

Ethernet-DKRev. 0.6 29Figure 26. µWeb Embedded Web Server

Ethernet-DKRev. 0.6 33. Hardware SetupThe following instructions illustrate how to setup the hardware included with the kit.1. Connect the AB4 Ethern

Ethernet-DK30 Rev. 0.67. Example Source CodeThe Embedded Ethernet Development Kit includes example source code, libraries, and register definition fi

Ethernet-DKRev. 0.6 318. C8051F120 Target BoardThe Embedded Ethernet Development Kit includes a target board with a C8051F120 device pre-installed fo

Ethernet-DK32 Rev. 0.68.1. C8051F120 Target Board SchematicFigure 28. C8051F120 Target Board Schematic

Ethernet-DKRev. 0.6 339. AB4 Ethernet Development BoardThe Embedded Ethernet Development Kit includes the AB4 Ethernet Development Board designed to

Ethernet-DK34 Rev. 0.69.1. Expansion I/O Connector (J1)The 96-pin expansion I/O connector J1 is used to connect the AB4 Ethernet Development Board to

Ethernet-DKRev. 0.6 359.2. AB4 Board Schematic

Ethernet-DK36 Rev. 0.610. Silicon Laboratories IDE (Integrated Development Environment)The Silicon Laboratories IDE integrates a source-code editor,

Ethernet-DKRev. 0.6 37APPENDIX—SUPPORTED PROTOCOLSLink/Physical Layer:Ethernet (IEEE802.3)—Widely installed local area network link/physical layer.Int

Ethernet-DK38 Rev. 0.6DOCUMENT CHANGE LISTRevision 0.3 to Revision 0.4 Added Netfinder Example. Added note that R1 should be shorted with a zero ohm

Ethernet-DKRev. 0.6 39NOTES:

Ethernet-DK4 Rev. 0.64. Network SetupThe Embedded Ethernet Development Kit can be connected to an Ethernet network using a standard Ethernetcable (se

Ethernet-DK40 Rev. 0.6CONTACT INFORMATIONSilicon Laboratories Inc.400 W Cesar ChavezAustin, TX 78701Please visit the Silicon Labs Technical Support we

Ethernet-DKRev. 0.6 54.1. Network Setup ProcedureIf using a standard cable:1. Connect the AB4 Ethernet Development Board to an Ethernet wall outlet o

Ethernet-DK6 Rev. 0.64.2. Selecting an IP Address for the Embedded SystemFor a PC to recognize an embedded system on a network, its IP address and su

Ethernet-DKRev. 0.6 75. Software SetupThe included CD-ROM contains the Silicon Laboratories IDE, Keil C51 toolset, and documentation includingdatashe

Ethernet-DK8 Rev. 0.64. Unselect the “Install Raisonance Evaluation 8051 Toolset” option and select “Install Keil Evaluation 8051 Toolset”. Then pres

Ethernet-DKRev. 0.6 96. Embedded Ethernet TutorialNow that the Embedded Ethernet Development Kit hardware has been set up, the software installed, an